CONTACT US PHONE (905) 857-3316

INDUSTRIAL PAINT

V110 ACRYLIC METAL PRIMER

V110-Can-Cut

Corotech V110 Acrylic Metal Primer is a water-reducible, rust-inhibitive primer for steel, iron, and non-ferrous metal. It provides excellent adhesion to a range of hard-to-coat surfaces and can even be applied over tightly adhering rust. Designed for light-to-moderate industrial exposures, this product can be top coated with a wide variety of coatings.

  • High solids content
  • Suitable for occupied areas
  • Can be recoated in just 4 hours
  • Suitable for use in USDA-inspected facilities
  • Qualifies for LEED certification

Colorant Used: Can be tinted with 2 oz. of Universal colorant
Color System Supported: N/A

V175 WATERBORNE BONDING PRIMER

V175-Can-Cut

Corotech V175 Waterborne Bonding Primer is a one-component bonding primer that may also be used as a rust-inhibitive universal primer. This product bonds to various metals creating a solid foundation for finishing coats. This product may be finish coated with a wide variety of coatings including alkyds, acrylics, epoxies, urethanes and moisture cured urethanes. Because of its versatility on all metals, Waterborne Bonding Primer will replace traditional wash coat primers and offers an easier-to-use alternative for all projects.

  • Replaces traditional wash coat primers with an easier-to-use coating
  • Low VOC, soap and water clean-up
  • Bonds to all metal substrates including tough to coat chrome, brass, stainless and aluminum
  • Suitable for use in USDA inspected facilities
  • Qualifies for LEEDS credits

Colorant Used: N/A
Color System Supported: N/A

V142 SHOP PRIMER

V142-Can-Cut

Corotech V142 Shop Primer is an economical steel primer for commercial use in mild to moderate exposures. This product is ideal as a temporary transport coat on fabricated pieces or as an economical barrier primer. It is a temporary coating. This primer may be top-coated with a wide variety of finishes. However, finishes containing strong solvents (Ketones, Xylene, Toluene) may cause wrinkling or lifting of Shop Primer.

  • Economical protective coat
  • Accepts a wide variety of topcoats
  • Dry to the touch in 30 minute

Colorant Used: N/A
Color System Supported: N/A

V155 100% SOLIDS EPOXY PRE-PRIMER

V155-00-Can-Cut

Corotech V155 is a 2 part 100% Solids Epoxy Pre-Primer is formulated for use on both steel and masonry. For rusted steel where extensive surface preparation is needed, but not logistically possible, the penetrating properties and extended dry time — 16 hours at 77 °F — of this two-component epoxy seal crevices and other imperfections, promoting better adhesion for subsequent coats. For prepared masonry surfaces, V155 penetrates and seals, providing an excellent foundation for subsequent coats of Corotech epoxy floor coatings. The unique, 100% solids formula of V155 forms a sealed epoxy barrier that inhibits future corrosion.

  • Low viscosity easily fills voids and crevices
  • Does not shrink – eliminates craters
  • Chemical and fume resistant
  • Extended cure time allows maximum penetration
  • Seals previously coated concrete, masonry, and galvanized metal
  • Qualifies for LEED certification

Colorant Used: N/A
Color System Supported: N/A

V440 WATERBORNE AMINE EPOXY

V440-Can-Cut

Corotech V440 Waterborne Amine Epoxy is a 2 part epoxy formulated to provide good chemical, abrasion and impact resistance on a variety of commercial and industrial surfaces, including steel, iron, concrete, non-ferrous metals, wood and drywall. Particularly suited for use on concrete floors. This product can be applied to many existing generic coating types with less risk of lifting or wrinkling.

When used on floors, this product provides moderate- to heavy-duty protection in commercial environments exposed to frequent foot traffic and occasional traffic of lightweight rubber-tired vehicles, intermittent spillage of mild chemicals, occasional steam cleaning, and powerwashing.

  • Water cleanup, fast dry
  • Easy application with excellent adhesion
  • Very good resistance to water and chemicals
  • Excellent for use on basement floors
  • Meets qualifications for LEED when used over metal substrates
  • Suitable for use in USDA inspected facilities

V331 ACRYLIC SEMI-GLOSS DTM ENAMEL

V331-Can-Cut

Corotech V331 Acrylic Semi-Gloss DTM Enamel is a tough waterborne acrylic enamel that fights rust on metal and provides a smooth, durable finish on wood, drywall and masonry substrates. A special inhibitor in the formula prevents flash rust when applied to ferrous metal, and the smooth dry film is UV and moisture resistant.

  • For light-to-moderate industrial, commercial and select residential use
  • Excellent for metal, as well as wood, masonry, drywall and other surfaces
  • Resists flash rust on metal
  • Excellent for all corrugated metal sheeting
  • Can be used on galvanized and aluminum metal

Colorant Used: Universal

V341 PRE-CATALYZED WATERBORNE WALL EPOXY

V341-Can-Cut

Corotech V341 Pre-Catalyzed Semi-Gloss Wall Epoxy is a unique product provides epoxy toughness in a ready-to-use waterborne formula for walls, ceilings and trim (not ideal for floors). Low VOC and water cleanup make this product ideal for use in occupied areas. The cured film is scrubbable, resists water and common cleaning chemicals, and stands up to abrasion and marring. Excellent adhesion to many surfaces, including existing paint, drywall, primed masonry and primed metal.

  • Single pack – no catalyst
  • Tints to all colors
  • Qualifies for LEED
  • Excellent for retail, commercial, healthcare, schools and more
  • Low VOC and water cleanu

Colorant Used: Universal

V630 ANTI-SLIP AGGREGATE

V630-Can-Cut

Corotech V630 is a specially formulated anti-slip aggregate is designed to elevate the foot or wheel on a damp or wet surface, permitting the water to escape instead of causing the foot or wheel to hydroplane.

 

Colorant Used: N/A
Color System Supported: N/A